Teke Happymodel Mobula6 HD 1S 65mm Brushless Bwhoop FPV Racing Drone 19000KV Motor

Specifications: Model: Mobula6 HD Wheelbase: 65mm Size: 80*80*40mm Spare parts: Motor Mode: EX0802 19000KV Configu-ration:9N12P Stator Diamter: 8mm Stator Length: 2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm Weight(g): 1.7g No.of Cells(Lipo):1S only Propellers Gemfan 1219-3 Center Thickness: 5mm Prop Disk Diameter: 31mm Center Hole Inner diameter:1.0mm Weight: 0.28g Flight controller MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI receiver Built-in 5V 1A BEC Built-in voltage detection Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_7.HEX Default protocol: DSHOT600 Onboard Frsky SPI D8 receiver Version SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference (Transmitter and receiver 1 m from the ground): 100m~200m Onboard SPI receiver Version SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference (Transmitter and receiver 1 m from the ground): 100~200m Failsafe support External DSMX version Resolution: 1024/2048 Operating voltage: 3.3V Working current: 60MA Size: 15mm*10mm*5mm Antenna length: 30mm Protocol: DSM2/DSMX External TBS CRSF Nano receiver version Original TBS CROSSFIRE Receiver ,CRSF Protocol, Official TBS transmitter compatible Onboard 5.8g VTX Output power: 25mw Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready Camera Model: RunCam Split3-Lite Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3) Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps Video File Format: MOV Image Resolution: 2 MP TV Mode: NTSC (720*480)/PAL (720*576) Switchable Interface: JST 1.25mm / UART and SH 1.0mm Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III) Hole Distance of Installation: 25.5*25.5mm PCB Size: 29*29mm Lens Module Size: 14*14mm Lens Specs: M9 Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.) Working Current: 450mA @5V Lipo Battery Capacity: 250mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 55mmx12mmx7mm Weight: 6.5g Connector: PH2.0 Package Included: 1* Drone Frame 1* Crazybee F4 Lite flight control 4* EX0802 KV19000 1* Gemfan 1219 three-blade propeller (4cw + 4ccw) 1* Runcam Split3-lite 1080P HD camera + DVR 1* 5.8G 25mw 40ch vtx(Flight controller built-in) 4* 1S 250mah 30C LiHV battery 1* 1S Lipo / LIHV USB charger 1* Propeller disassemble tool

1. With 0802 KV19000 battery and Qianfeng 31mm propeller, it can ensure strong flight power whether it is flying indoors or outdoors.2. Crazybee F4 Lite version flight controller supports 1S lithium battery (lihV). Integrate Betaflight OSD function, keep abreast of the flight voltage, receiver signal, and fly more calmly3. 1S indoor whoop traversing machine, with 0802 motor, strong power. VTX comes with Smartaudio function, you can adjust the flight control parameters through the OSD, adjust the flight control PID, and adjust the VTX frequency point parameters.4. Support Betaflight tuning, multiple flight modes, integrated injection molding Tiny Whoop structure.5. Highly integrated motherboards integrate OSD, Dshot ESC, 2.4G SPI receiver, 5.8g 25mw 40CH VTX.