Edelbrock 1405 Performer 600 CFM Manual Carb/Air/Fuel Kit,Pro-Flo

Top off your engine with these carburetor air/fuel installation kits. Complete installation kit includes mounting hardware. Kit Includes: (1) Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke. (1) Edelbrock 1208 Pro-Flo Chrome Air Cleaner Assembly, Round, 2 Inch. (1) Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet. (1) 1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI. (1) Carburetor Stud Kit, 1-3/8 Inch. Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke Edelbrock Performer Series carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock four barrel carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series four barrel carbs are the best choice for performance and value. All Edelbrock products are proudly made in the U.S.A. Designed and calibrated for optimum street performance in small-block and some big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II and other brands of similar design. This 4 barrel carb includes manual choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately. Features: Manual choke. Bolt-on-and-run performance right out of the box. Smooth throttle response throughout the power band. Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel. Float levels are factory set; adjustments are rarely needed. Change jets, adjust floats & replace needles/seats without draining fuel or removing carb. Two-piece design means no gaskets below the fuel level for leak-free operation. Lightweight all-aluminum body is compatible with gasohol and blended fuels. Includes both timed and full vacuum ports for ignition advance. Edelbrock 1208 Pro-Flo Chrome Air Cleaner Assembly, Round, 2 Inch Stamped From 18-Gauge Steel. Triple-Chrome Plated. High-Quality Finish. Great Looks. Works With All 5.125 in. Carbs. Great for applications with low hood clearance. Base Knock-Outs For Use w/Crankcase Ventilation. Adapter For Crankcase Ventilation # 1205 not included, available separately. 10 Inch diameter. 2 Inch Filter Height. Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet 3/8” fuel line kits have a clean look and are easy to install. Fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. Drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. Includes a barbed end for a push-on 3/8" rubber fuel line. Manufactured of chrome plated steel. Include a 5/8" -20 threaded banjo bolt with gaskets. 1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI Appropriate fuel pressure is important for adjusting your fuel system to achieve optimal performance, which means an accurate pressure gauge is equally important. Built for superior precision. Liquid filled and available for carbureted and fuel injected applications. 0-15 PSI. 1-1/2" diameter. Carburetor Stud Kit, 1-3/8 Inch Easy installation/removal of carb plates. Includes zinc plated steel studs, nuts and washers. 1-3/8" tall.

Delivers smooth throttle response throughout the power band Lightweight all-aluminum body is compatible with gasohol and blended fuels Edelbrock Pro-Flo air cleaner is stamped from high quality 18-gauge steel with a triple-chrome plated finish Fuel line is designed to provide a clean and custom plumbing solution All Edelbrock products are proudly made in the U.S.A