JBL CSMA280 Commercial/Restaurant 2x80w Amplifier+White Wall Volume Controllers

Package Includes: (1) JBL CSMA280 Commercial/Restaurant 2 x 80w Amplifier 4ohm/8ohm/70V/100V, 8 inputs (2) JBL CSR-V White Wall Volume Controller For Select CSM/CSMA/VMA Mixer Amplifiers Specifications of CSMA280: Maximum Output Power: 800 W per channel into 4 Ohms or 8 Ohms, 1 kHz, = 0.5% THD Insertion Loss: 1 dB maximum for 70 and 100 V outputs Continuous Power: 10 W per channel Line Output Level: 5.0 V RMS into 10 kOhms Input Sensitivity: To obtain full rated power at 8 Ohms (or 5 VRMS to line output). Mic Input: 3 mV RMS. Line Input: 775 mV RMS. RCA Input: 300 mV RMS Number of Channels: Input: 8, Output: 2. Frequency Response: Measured at 2.83 V RMS into rated load impedance at any output. 4/8 Ohms Output: 20 Hz - 20 kHz, ±2 dB. 70 V/100 V Outputs: 80 Hz - 15 kHz ±2 dB. Line Out: 20 Hz - 20 kHz, ±1 dB Total Harmonic Distortion (THD): Measured at 2.83 V RMS into rated load impedance at any output. Power Amplifier Output: <0.5%, 20 Hz to 20 kHz. Line Output: 0.05% typical Signal to Noise Ratio: > 90 dB Nominal Input Impedance: Mic: 400 Ohms. Line: 20 kOhms (balanced). RCA: 50 kOhms. Minimum Load Impedance: Low Impedance Output: 4 Ohms. 70 V Output: 120 Ohms. 100 V Output: 240 Ohms. Crosstalk: -70 dB @ 1 kHz Controls: Front Panel: 8 x Input level rotary knobs 2 x Output volume-attenuating knobs 1 x Power switch 2 x Bass potentiometers 2 x Treble potentiometers Rear Panel: 2 x Input-routing dip switches (including phantom and Hi-Z switches) 8 x Mic/Line selector switch 2 x Vox adjustment switches Indicators: Front Panel: 8 x Input signal presence ring, green 2 x Output volume ring, green 1 x Power switch ring, green/blue Connectors: Rear Panel: 1 x IEC power input 2 x Aux out connection points 6 x 3-pin euroblock connectors 6 x 3-pin euroblock connectors 2 x 5-pin euroblock connectors 6 x Dual RCA input connectors 2 x RJ45, remote volume Operating Temperature / Humidity: 32 to 95°F / 0 to 35°C, 95% RH (non-condensing) Storage Temperature: -4 to 185°F / -20 to 85°C Phantom Power: 27 VDC AC Input: 100-240 VAC, 50/60 Hz Dimensions (W x D x H): 17.2 x 11.9 x 1.7" / 436.9 x 302.3 x 43.2 mm Weight: Approximately 11.9 lb / 5.4 kg Description of CSR-V-WHT: The JBL Commercial® CSR series remote controls allow analog DC voltage to provide logic control ranging from source selection and volume. Wired with Cat 5 cable with universally accepted RJ-45 connectors up to 1000 feet (305 m) length, the CSR series remote controls allow you to remotely select the source and/or control the volume on the CSM mixer. Using CSR-V remote control with your CSM mixer, you can remotely control the volume of the source selected by the mixer. Features: JBL CSR-V White Wall Volume Controller For Select CSM/CSMA/VMA Mixer Amplifiers Color: White For CSM-21 & CSM-32 Mixers Controls Volume Dual RJ45 Connectors Uses Cat 5 Cable

Package Includes: (1) JBL CSMA280 Commercial/Restaurant 2 x 80w Amplifier 4ohm/8ohm/70V/100V, 8 inputs. (2) JBL CSR-V White Wall Volume Controller For Select CSM/CSMA/VMA Mixer Amplifiers. Features: JBL CSMA280 Commercial/Restaurant 2 x 80w Amplifier 4ohm/8ohm/70V/100V and 8 inputs. For Commercial and Industrial Use. 80W into 8 or 4 Ohm Loads. 10W Per Channel. 8 Input Channels, 2 Output Channel. Usable with 70 & 100V Systems. Euroblock Mic/Line & RCA Inputs. Hi-Z & 27V Phantom Power Switches Sleep Mode & 2 Auxiliary Outputs. Voice Activated Ducking & Priority Mute. Specifications: Maximum Output Power: 800 W per channel into 4 Ohms or 8 Ohms, 1 kHz, = 0.5% THD. Insertion Loss: 1 dB maximum for 70 and 100 V outputs. Continuous Power: 10 W per channel. Line Output Level: 5.0 V RMS into 10 kOhms. Input Sensitivity: To obtain full rated power at 8 Ohms (or 5 VRMS to line output). Mic Input: 3 mV RMS. Line Input: 775 mV RMS. RCA Input: 300 mV RMS Number of Channels: Input: 8, Output: 2.. Frequency Response: Measured at 2.83 V RMS into rated load impedance at any output. 4/8 Ohms Output: 20 Hz - 20 kHz, ±2 dB. 70 V/100 V Outputs: 80 Hz - 15 kHz ±2 dB. Line Out: 20 Hz - 20 kHz, ±1 dB. Total Harmonic Distortion (THD): Measured at 2.83 V RMS into rated load impedance at any output. Power Amplifier Output: <0.5%, 20 Hz to 20 kHz. Line Output: 0.05% typical. Signal to Noise Ratio: > 90 dB Nominal Input Impedance: Mic: 400 Ohms. Line: 20 kOhms (balanced). RCA: 50 kOhms.. Minimum Load Impedance: Low Impedance Output: 4 Ohms. 70 V Output: 120 Ohms. 100 V Output: 240 Ohms.. Crosstalk: -70 dB @ 1 kHz. Controls: Front Panel: 8 x Input level rotary knobs. 2 x Output volume-attenuating knobs. 1 x Power switch. 2 x Bass potentiometers. 2 x Treble potentiometers. Rear Panel: 2 x Input-routing dip switches (including phantom and Hi-Z switches). 8 x Mic/Line selector switch 2 x Vox adjustment switches. Indicators: Front Panel: 8 x Input signal presence ring, green. 2 x Output volume ring, green. 1 x Power switch ring, green/blue. Connectors: Rear Panel: 1 x IEC power input. 2 x Aux out connection points. 6 x 3-pin euroblock connectors. 6 x 3-pin euroblock connectors. 2 x 5-pin euroblock connectors. 6 x Dual RCA input connectors. 2 x RJ45, remote volume. Operating Temperature / Humidity: 32 to 95°F / 0 to 35°C, 95% RH (non-condensing)